利用相似理论和量纲分析进行颗粒缩放，将粒径0.5 mm的铸铁煤粉颗粒放大至2 mm，进行虚拟实验标定放大颗粒的基本接触参数，用离散单元模型模拟垂直螺旋输送中的颗粒运动，验证颗粒缩放法的准确性. 结果表明，螺旋转速为500, 550, 600, 650 r/min时，颗粒轴向速度和圆周速度增大，最大轴向速度位于中上部，处于叶片边缘，分别为0.486, 0.535, 0.596, 0.657 m/s，超过螺旋叶片半径区域的颗粒轴向速度明显减小；相同填充率下，装置出口处质量流率、颗粒轴向速度模拟值和实验值基本吻合，满足相似理论.
With the principles of similarity and dimensional analysis, the cast iron pulverized coal was enlarged from 0.5 mm to 2 mm. The virtual experiment was carried out to calibrate the basic contact parameters of scaled particles. The simulation of particle movement in vertical screw conveyor with discrete element model was carried out to verify the exactness of the scaling method. The results showed that when the screw rotation speed is 500, 550, 600, 650 r/min, particle axial velocity and peripheral speed is increased. The maximum axial velocity is in the upper part and on the verge of blade, respectively 0.486, 0.535, 0.596, 0.657 m/s. The axial velocity decreases obviously in area more than spiral radius. Compared with simulation and experiment, the mass flow rate in the device outlet and particle axial velocity is true on the whole and meets the principles of similarity under the reasonable approximations.
[ ] 赵占一, 孟文俊, 孙晓霞,等. 垂直螺旋输送机中颗粒速度的分布[J]. 过程工程学报, 2015, 15(6):909-915.
Zhao Z Y, MENG W J, SUN X X, et, al. Distribution of Particle Velocity in a Vertical Screw Conveyor[J]. The Chinese Journal of Process Engineering, 2015，15(6): 909-915.
[ ] 李海燕. 基于EDEM的垂直螺旋输送机性能参数仿真研究[D]. 太原科技大学, 2011.
Li H Y. Parameters of numerical simulation and research of the vertical screw conveyor performance based on EDEM[D]. Taiyuan University of Science and Technology, 2011
[ ] Owen P J, Cleary P W. Prediction of screw conveyor performance using the Discrete Element Method (DEM)J. Powder Technology, 2009, 193(3): 274-288.
[ ] Feng Y T, Owen D R J. Discrete element modelling of large scale particle systems—I: exact scaling laws[J]. Computational Particle Mechanics, 2014, 1(2):159-168.
[ ] Sakai M, Abe M, Shigeto Y, et al. Verification and validation of a coarse grain model of the DEM in a bubbling fluidized bed[J]. Chemical Engineering Journal, 2014, 244(10):33–43.
[ ] Hertz B H. On the contact of elastic solids. Zeitschrift fur Reine und Angewandte Mathematik 92, 156--171 (1882). English translation[C]// Miscellaneous Papers. 2010.
[ ] Mindlin R D. Compliance of Elastic Bodies in Contact[C]// 1949:259-268.
[ ] Feng Y T, Han K, Owen D R J, et al. On upscaling of discrete element models: similarity principles[J]. Engineering Computations, 2009, 26(6):599-609.
[ ] Pezo L, Jovanovi? A, Pezo M, et al. Modified screw conveyor-mixers – Discrete element modeling approach[J]. Advanced Powder Technology, 2015, 26(5):1391-1399.
[ ] Boac J M, Casada M E, Maghirang R G, et al. Material and interaction properties of selected grains and oilseeds for modeling discrete particles[J]. Transactions of the ASABE, 2010, 53(4): 1201-1216.
[ ] 张桂花, 汤楚宙, 熊远福,等. 包衣稻种物理特性的测定及其应用[J]. 湖南农业大学学报:自然科学版, 2004, 30(1):68-70.
Zhang G H, Tang Y Z, Xiong Y F, et, al.Measurement and Application of the Capsuled Seed Physical Characteristics[J]. Journal of Hunan Agricultural University, Natural Sciences, 2004, 30(1):68-70.
[ ] Owen P J. Screw conveyor performance: comparison of discrete element modelling with laboratory experiments[J]. Progress in Computational Fluid Dynamics An International Journal, 2010, 10(5):327-333.
[ ] 任建莉, 胡维骏, 王勤勇,等. 垂直螺旋输送机气固两相流的试验及数值模拟[J]. 计算机与应用化学, 2016, 33(6):663-669
Ren J L, Hu W J, W Q Y, at, al. Experiment and numerical simulation of gas-solid two-phase flow in vertical screw conveyor[J]. Computers and Applied Chemistry, 2016, 33(6):663-669
[ ] 梅磊. 螺旋卸船机垂直输送机理及试验研究[D]. 武汉理工大学, 2014.
Mei L. Conveying Mechanical Analysis and Experiment of Vertical Upgrading of Screw Unloader[D]. Wuhan University of Technology. 2014
[ ] Mcbride W, Cleary P W. An investigation and optimization of the ‘OLDS’ elevator using Discrete Element Modeling[J]. Powder Technology, 2009, 193(3):216-234.
