欢迎访问过程工程学报, 今天是

过程工程学报 ›› 2026, Vol. 26 ›› Issue (7): 761-770.DOI: 10.12034/j.issn.1009-606X.225276

• 研究论文 • 上一篇    下一篇

高频交流电场下液滴运动特性及影响因素分析

王余豪1,2， 陈家庆1,2,4*， 石熠1,2， 吴红军5， 王秀军3， 张健3， 陈翔宇3   

  1. 1. 北京石油化工学院机械工程学院，北京 102617 2. 深水油气管线关键技术与装备北京市重点实验室，北京 102617 3. 海洋油气高效开发全国重点实验室，北京 102209 4. 北方工业大学机械与材料工程学院，北京 100144 5. 东北石油大学新能源与材料学院，黑龙江 大庆 163318
  • 收稿日期:2025-10-30 修回日期:2025-12-19 出版日期:2026-07-28 发布日期:2026-07-28
  • 通讯作者: 陈家庆 Jiaqing@bipt.edu.cn
  • 基金资助:
    国家自然科学基金项目;国家科技重大专项;国家自然科学基金项目

Analysis of droplet dynamics and influencing factors under high-frequency AC electric field

Yuhao WANG1,2,  Jiaqing CHEN1,2,4*,  Yi SHI1,2,  Hongjun WU5,  Xiujun WANG3,  #br# Jian ZHANG3,  Xiangyu CHEN3   

  1. 1. School of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617, China 2. Beijing Key Laboratory of Key Technologies and Equipment for Deepwater Oil and Gas Pipelines, Beijing 102617, China 3. National Key Laboratory of Offshore Oil and Gas Exploitation, Beijing 102209, China 4. School of Mechanical and Material Engineering, North China University of Technology, Beijing 100144, China 5. College of New Energy and Materials Science, Northeast Petroleum University, Daqing, Heilongjiang 163318, China
  • Received:2025-10-30 Revised:2025-12-19 Online:2026-07-28 Published:2026-07-28
  • Contact: Jia-qing CHEN Jiaqing@bipt.edu.cn

RichHTML

PDF

摘要： 为阐明高频/高压脉冲交流电场中化学破乳剂、温度及聚合物对油包水型乳化液中分散相液滴变形与聚并行为的影响规律，本工作采用显微高速摄像技术系统分析了不同因素对液滴运动的作用机制。结果表明，仅电场作用时，液滴变形度随场强增加而增大，破碎临界场强为5.0 kV/cm；双液滴聚并的最优电场参数为电场强度3.0 kV/cm、电场频率2.5 kHz。升温可促进液滴变形，降低其破碎临界场强，并缩短两液滴接触时间，但温度过高不利于液滴聚并。电场与破乳剂协同作用时，最优破乳剂浓度为100 mg/L，在3.0 kV/cm下两液滴接触时间最短为6 ms。聚合物的存在会抑制液滴变形并提高聚并所需场强，通过加入破乳剂和升温则可有效促进聚并，提升破乳效率。本研究结果可为聚合物驱采出液处理用高效破乳脱水设备操作参数的选取提供参考和指导。

关键词: 液滴聚并, 高频/高压脉冲交流电场, 破乳剂, 温度效应, 聚合物

Abstract: To clarify the effects of chemical demulsifiers, temperature, and polymers on the deformation and coalescence behaviors of dispersed droplets in water-in-oil emulsions under high-frequency/high-voltage pulsed alternating current (AC) electric field, microscopic high-speed photography was employed to systematically analyze the mechanisms of droplet movement influenced by different factors. The results showed that under the electric field alone, the degree of droplet deformation increased with the increase of electric field strength, and the critical electric field strength for droplet breakup was 5.0 kV/cm; the optimal electric field parameters for the coalescence of two droplets were 3.0 kV/cm and 2.5 kHz. Increasing temperature could enhance droplet deformation, reduce its critical electric field strength for breakup, and shorten the contact time between the two droplets. However, excessively high temperature was not conducive to droplet coalescence. When the electric field was used synergistically with a demulsifier, there was an optimal demulsifier concentration of 100 mg/L. The shortest contact time between the two droplets was 6 ms when the electric field strength was 3.0 kV/cm. The presence of polymer would inhibited droplet deformation and increased the electric field strength required for coalescence. However, the addition of a demulsifier and an increase in temperature could effectively promote coalescence and improve demulsification efficiency. The findings of this study can provide theoretical support and practical guidance for determining operating parameters of high-efficiency demulsification and dehydration equipment for the treatment of polymer flooding production fluid.

Key words: droplet coalescence, high-frequency/high-voltage pulsed AC electric field, demulsifier, temperature effect, polymer